快乐飞艇全天两期计划

Model BDLR19 is a minimum pressure accumulation conveyor which can provide an economical means of accumulating products with minimal back pressure. This conveyor can be supplied with close roller centers, and is a reliable choice for package, carton or tote handling applications.

Download PDF

BETWEEN FRAMES: 15″ – 39″
LENGTH: 60″ – 1200″
BEGINNING ELEVATION: 8.75″ – 126″
ENDING ELEVATION: 8.75″ – 126″
SPEED: 10 – 200 FPM
ROLLER CENTERS: 3″, 4″, 6″
BELT: Standard belt is Trackmate 120 EMB with clipper lace. Optional belts include Trackmate Roughtop, PVC white, Food grade white polyurethane thermoplastic and Slip Top latex belts.
DRIVE: Standard drive is end, right hand side. Optional drives include End drive left hand side or Center drive right hand side
MOTOR: 1/2 HP through 1-1/2 HP. Energy efficient and inverter duty motors also available. Voltages include 120/1/60, 230/3/60, 460/3/60 and 575/3/60 & DC Voltage.
ROLLER COVERS: Optional roller coverings include galvanized roller tube and polyurethane roller sleeves.
SUPPORT CENTERS: Standard supports are floor supports on 10’ centers. Optional supports on 5’ centers. Ceiling supports are also available.
FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors include green, beige, gray, orange, black and yellow.

Model BDR19N is a narrow belt drive, minimum pressure accumulation conveyor with an economical design well suited for accumulation of light weight loads. The narrow belt allows options for smaller between frame widths than the standard BDLR19 conveyor.

Download PDF

BETWEEN FRAMES: 13″ – 39″
LENGTH: 60″ – 480″
BEGINNING ELEVATION: 18″ – 72″
ENDING ELEVATION: 18″ – 72″
SPEED: 30, 40, 50, 60, 90, 200 FPM
ROLLER CENTERS: 3″, 4″, 6″
BELT: 1-1/4” wide 3 ply power transmission belt with polyester traction top cover.
DRIVE: Standard drive is center drive, right.
MOTOR: 1/2 HP, Energy efficient and inverter duty motors also available. Voltages include 120/1/60, 230/3/60, 460/3/60 and 575/3/60 & DC Voltage.
ROLLER: 1.9″ diameter 16 gauge tube with 7/16″ hex cold rolled steel axle, spring retained with precision bearings. 1.9″ diameter 12 gauge and 9 gauge rollers are available as option.
MINIMUM PRESSURE ACCUMALATION: Pressure is set by using adjusting pressure idlers as needed to create minimum pressure drive of carrying surface rollers.
SUPPORT CENTERS: Standard supports are floor supports on 10’ centers. Optional ceiling supports are also available.
FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors include green, beige, gray, orange, black and yellow.

Model BDLR25 is a heavy duty, minimum pressure accumulation conveyor which provides an effective means of accumulating heavier products with minimal back pressure. This conveyor can be effective for loads that require higher capacity rollers on closer centers.

Download PDF

BETWEEN FRAMES: 15″ – 57″
LENGTH: 60″ – 960″
BEGINNING ELEVATION: 12″ – 108″
ENDING ELEVATION: 12″ – 108″
SPEED: 10 – 120 FPM
ROLLER CENTERS: 3″, 4″, 6″
ZONE LENGTH: 36″, 48″, 60″, 72″, 84″
ROLLERS: BDLR25 Roller – 2.50” diameter, 11ga wall tube. BDLR26 Roller – 2.625” diameter, 7ga wall tube. All rollers with 11/16” hex cold rolled steel axles, spring retained. Standard bearings are precision, grease packed bearings.
BELT: Standard 12” wide Trackmate PVC120 with clipper lacing supported on 1.9” diameter 16 gauge rollers with precision bearings. Optional non-woven NBR Ultimate.
DRIVE: Standard drive is an end drive, right hand side. Optional drives include end drive, left hand side; and center drive, right hand side.
MOTOR: 3/4 HP through 1-1/2 HP, Energy efficient and inverter duty motors also available. Voltages include 120/1/60, 230/3/60, 460/3/60, 575/3/60 & DC Voltage.
MINIMUM PRESSURE ACCUMULATION: Drive force is set by making adjustments to the pressure roller adjusting rods, typically located on 60″ centers.
ROLLER SURFACE: Standard roller surface is carbon steel. Optional surface for 2.5” rollers includes galvanized roller tube.
SUPPORT CENTERS: Standard supports are floor supports on 5’ centers. Optional on 10’ centers.
FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors include green, beige, gray, orange, black and yellow.

Model BDLR26 is a heavy duty, minimum pressure accumulation conveyor which provides an effective means of accumulating heavier products with minimal back pressure. This conveyor offers the same features of our BDLR25, with the added benefit of rugged, heavy wall rollers.

Download PDF

BETWEEN FRAMES: 15″ – 57″
LENGTH: 60″ – 960″
BEGINNING ELEVATION: 12″ – 108″
ENDING ELEVATION: 12″ – 108″
SPEED: 10 – 120 FPM
ROLLER CENTERS: 3″, 4″, 6″
ZONE LENGTH: 36″, 48″, 60″, 72″, 84″
ROLLERS: BDLR25 Roller – 2.50” diameter, 11ga wall tube. BDLR26 Roller – 2.625” diameter, 7ga wall tube. All rollers with 11/16” hex cold rolled steel axles, spring retained. Standard bearings are precision, grease packed bearings.
BELT: Standard 12” wide Trackmate PVC120 with clipper lacing supported on 1.9” diameter 16 gauge rollers with precision bearings. Optional non-woven NBR Ultimate.
DRIVE: Standard drive is an end drive, right hand side. Optional drives include end drive, left hand side; and center drive, right hand side.
MOTOR: 3/4 HP through 1-1/2 HP, Energy efficient and inverter duty motors also available. Voltages include 120/1/60, 230/3/60, 460/3/60, 575/3/60 & DC Voltage.
MINIMUM PRESSURE ACCUMULATION: Drive force is set by making adjustments to the pressure roller adjusting rods, typically located on 60″ centers.
ROLLER SURFACE: Standard roller surface is carbon steel. Optional surface for 2.5” rollers includes galvanized roller tube.
SUPPORT CENTERS: Standard supports are floor supports on 5’ centers. Optionalon 10’ centers.
FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors include green, beige, gray, orange, black and yellow.

Model MDTLRC is a belt driven live roller curve that can provide positive drive for negotiating 90, 45, and 30 degree turns. Used in light and medium duty applications, the tapered rollers help maintain product orientation through the curve.

Download PDF

BETWEEN FRAMES: 13″, 15″, 17″, 19″, 21″, 23″, 25″, 27″, 31″, 33″, 37″, 39″
DEGREE: 30, 45, 90
BEGINNING ELEVATION: 7.5″ – 126″
ENDING ELEVATION: 7.5″ – 126″
SPEED: 30, 40, 50, 60, 90, 200 FPM
BELT: Endless B-section V-Belt support.
ROLLERS: 2-1/2” diameter tapered to 1-11/16” diameter, 14ga with precision grease packed bearings, 7/16” spring retained hex axle. Tangent sections use 1.9″ diameter, 16ga with precision grease packed bearings, 7/16” spring retained hex axle.
DRIVE: Standard drive is an End Drive, right hand side. Optional drive includes End drive left hand side.
MOTOR: 1/2 HP. Energy efficient and inverter duty motors also available. Voltages include 120/1/60, 230/3/60, 460/3/60 and 575/3/60 & DC Voltage.
SUPPORT CENTERS: Standard supports are floor supports on 10’ centers. Optional on 5’ centers. Ceiling supports are also available.
FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors include green, beige, gray, orange, black and yellow.

Model MDTLRS is a combination spur and curve live roller conveyor used to divert off, or merge on, main trunk line conveyors at various angles. This unit is offered in 30, 45, and 60 degree options.

Download PDF

BETWEEN FRAMES: 13″, 15″, 17″, 19″, 21″, 23″, 25″, 27″, 31″, 33″, 37″, 39″
DEGREE: 30, 45
BEGINNING ELEVATION: 7.5″ – 126″
ENDING ELEVATION: 7.5″ – 126″
SPEED: 30, 40, 50, 60, 90, 200 FPM
BELT: Endless B-section V-Belt support.
ROLLERS: 2-1/2” diameter tapered to 1-11/16” diameter, 14ga with precision grease packed bearings, 7/16” spring retained hex axle. Tangent section s use 1.9″ diameter, 16ga with precision grease packed bearings, 7/16” spring retained hex axle.
DRIVE: Standard drive is an End Drive, right hand side. Optional drive includes End drive left hand side.
MOTOR: 1/2 HP. Energy efficient and inverter duty motors also available. Voltages include 120/1/60, 230/3/60, 460/3/60 and 575/3/60 & DC Voltage.
SUPPORT CENTERS: Standard supports are floor supports on nominal 5’ centers.
FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors include green, beige, gray, orange, black and yellow.

Model ZPLR19 is a medium duty, zero pressure accumulation conveyor which can provide accumulation of light to medium weight loads with no back pressure. These units come equipped with zone control logic with easy set-up for cascade or slug release modes.

Download PDF

BETWEEN FRAMES: 15″ – 39″
LENGTH: 72″ – 840″
BEGINNING ELEVATION: 12″ – 60″
ENDING ELEVATION: 12″ – 60″
SPEED: 10 – 120 FPM
ROLLER CENTERS: 3″, 4″, 6″
ROLLERS: Standard rollers are 1.9″ diameter with 7/16″ hex cold rolled steel axles, spring retained, grease packed bearings. 1916 roller has 16ga wall tube, precision bearings. 1912 roller has 12ga wall tube, precision bearings. 1909 roller has 9ga wall tube, semi-precision bearings.
BELT: Standard belt is Trackmate 120 EMB with clipper lace.
DRIVE: Standard drive is end, right hand side. Optional drives include End drive left hand side or Center drive right hand side
MOTOR: 1/2 HP through 1-1/2 HP. Energy efficient and inverter duty motors also available. Voltages include 115/1/60, 208/3/60, 230/3/60, 460/3/60 and 575/3/60 & DC Voltage.
ROLLER SURFACE: Standard roller surface is carbon steel. Optional galvanized surface for 1912 and 1916 rollers.
SUPPORT CENTERS: Standard supports are floor supports on 10’ centers. Optional supports on 5’ centers. Ceiling supports are also available.
FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors include green, beige, gray, orange, black and yellow.
ACCUMULATION ZONES: Zone length is a multiple of roller center. Recommended zone length is 12″ longer than longest product length. Standard zone logic is for cascading accumulation.
TREAD ROLLER BRAKE: Friction type brake is actuated automatically with zone actuation to prevent coasting of product in the accumulation zones.
AIR REQUIREMENTS: Requires 40PSI air pressure of clean, filtered air at consumption of approximately 0.05 cubic feet per sensor actuation.
FILTER REGULATOR: Supplied for main air supply at input, 3/8″ NPT port.
POWER SUPPLY: Includes 24 VDC power supply located near center of conveyor and capable of supplying power for up to 50 zones.

Model ZPLR25 is a heavy duty, zero pressure accumulation conveyor which can provide accumulation of heavier loads with no back pressure. These units come equipped with zone control logic with easy set-up for cascade or slug release modes.

Download PDF

BETWEEN FRAMES: 15″ – 57″
LENGTH: 72″ – 960″
BEGINNING ELEVATION: 12″ – 108″
ENDING ELEVATION: 12″ – 108″
SPEED: 10 – 120 FPM
ROLLER CENTERS: 3″, 4″, 6″
ROLLERS: ZPLR25 Roller – 2.50″ diameter, 11ga wall tubes. ZPLR26 Roller – 2.625″ diameter, 7ga wall tubes. All rollers with 11/16″ hex cold rolled steel axles, spring retained. Standard bearings are precision, grease packed bearings.
BELT: Standard belt is Trackmate PVC120 with clipper lace.
DRIVE: Standard drive is end, right hand side. Optional drives include End drive left hand side or Center drive right hand side
MOTOR: 1/2 HP through 1-1/2 HP. Energy efficient and inverter duty motors also available. Voltages include 115/1/60, 208/3/60, 230/3/60, 460/3/60 and 575/3/60 & DC Voltage.
ROLLER SURFACE: Standard roller surface is carbon steel. Optional surface for 2.5″ rollers includes galvanized roller tube.
SUPPORT CENTERS: Standard supports are floor supports on 10’ centers. Optional supports on 5’ centers. Ceiling supports are also available.
FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors include green, beige, gray, orange, black and yellow.
ACCUMULATION ZONES: Zone length is a multiple of roller center.
Recommended: zone length is 12″ longer than longest product length. Standard zone logic is for cascading accumulation.
TREAD ROLLER BRAKE: Friction type brake is actuated automatically with zone actuation to prevent coasting of product in the accumulation zones.
AIR REQUIREMENTS: Requires 40PSI air pressure of clean, filtered air at consumption of approximately 0.05 cubic feet per sensor actuation.
FILTER REGULATOR: Supplied for main air supply at input, 3/8″ NPT port.
POWER SUPPLY: Includes 24 VDC power supply located near center of conveyor and capable of supplying power for up to 50 zones.

Model FTFRB is a roller bed, inclined belt conveyor used to transport product up or down at angles up to 30 degrees. Due to the heavy bed section, it is often used in industrial applications and therefore capable of moving heavier loads with less power.

Download PDF

BELT WIDTH: 12″, 18″, 24″, 30″, 36″
LENGTH: 120″ – 600″
BEGINNING ELEVATION: 7.5″ – 99″
ENDING ELEVATION: 7.5″ – 240″
SPEED: 3 – 150 FPM
FLOOR TO FLOOR HEIGHT: 0″ – 240″
NOSEOVER LENGTH: 27″ – 120″
INCLINED ANGLE: 10 – 25
FEEDER LENGTH: 48″ – 120″
ROLLER CENTERS: 3″, 4.5″, 6″
BELT: Standard belt is Trackmate Roughtop with clipper lace. Optional belts include.
DRIVE: Standard drive is Center drive right hand. Optional drive is Center drive left hand.
FEEDER: Optional feeder available.
MOTOR: 3/4 HP through 2 HP. Energy efficient and inverter duty motors also available. Voltages include 120/1/60, 230/3/60, 460/3/60, 575/3/60 & DC Voltage.
SUPPORT CENTERS: Standard supports are for two floor applications. Optional supports include tall floor supports (120” maximum) and ceiling hangers for elevated sections.
FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors include green, beige, gray, orange, black and yellow.

Model ZPLR26 is a heavy duty, zero pressure accumulation conveyor which can provide accumulation of heavier loads with no back pressure. These units come equipped with zone control logic with easy set-up for cascade or slug release modes. This conveyor offers the same features of our BDLR25, with the added benefit of rugged, heavy wall rollers.

Download PDF

BETWEEN FRAMES: 15″ – 57″
LENGTH: 72″ – 960″
BEGINNING ELEVATION: 12″ – 108″
ENDING ELEVATION: 12″ – 108″
SPEED: 10 – 120 FPM
ROLLER CENTERS: 3″, 4″, 6″
ROLLERS: ZPLR25 Roller – 2.50″ diameter, 11ga wall tubes. ZPLR26 Roller – 2.625″ diameter, 7ga wall tubes. All rollers with 11/16″ hex cold rolled steel axles, spring retained. Standard bearings are precision, grease packed bearings.
BELT: Standard belt is Trackmate PVC120 with clipper lace.
DRIVE: Standard drive is end, right hand side. Optional drives include End drive left hand side or Center drive right hand side
MOTOR: 1/2 HP through 1-1/2 HP. Energy efficient and inverter duty motors also available. Voltages include 115/1/60, 208/3/60, 230/3/60, 460/3/60 and 575/3/60 & DC Voltage.
ROLLER SURFACE: Standard roller surface is carbon steel. Optional surface for 2.5″ rollers includes galvanized roller tube.
SUPPORT CENTERS: Standard supports are floor supports on 10’ centers. Optional supports on 5’ centers. Ceiling supports are also available.
FRAME FINISH: Standard finish is OSHA safety blue powder. Optional colors include green, beige, gray, orange, black and yellow.
ACCUMULATION ZONES: Zone length is a multiple of roller center.
Recommended: zone length is 12″ longer than longest product length. Standard zone logic is for cascading accumulation.
TREAD ROLLER BRAKE: Friction type brake is actuated automatically with zone actuation to prevent coasting of product in the accumulation zones.
AIR REQUIREMENTS: Requires 40PSI air pressure of clean, filtered air at consumption of approximately 0.05 cubic feet per sensor actuation.
FILTER REGULATOR: Supplied for main air supply at input, 3/8″ NPT port.
POWER SUPPLY: Includes 24 VDC power supply located near center of conveyor and capable of supplying power for up to 50 zones.